Miscellaneous Valves

Miscellaneous Valves

        • 1/4" Three-Way Gauge Valve

          • Specifically designed for fire sprinkler system pressure gauges 
          • One 1/4" inlet and two 1/4" outlets
          • Allows for replacement of the system gauge without shutting down the water supply to the sprinkler system 
          • Test system pressure with an additional gauge through the second outlet
          • UL Listed
          0.0
          Add first review
          Not rated yet
              • Ball Drip Valve - 1/2" x 1/4"

                Ball Drip Valve - 1/2" x 1/4"


                The solid brass ball drip is a “ball” type check valve. When properly installed, the internal ball rests in the lower most area of the valve body allowing for proper drainage of moisture accumulation. Upon system pressurization, the internal ball is “pushed” into the small end of the ball drip body closing the opening. When system pressure is removed, the ball returns to its original position. One of the most common uses is on the dry side of the Fire Department Connection valve. This use helps keep moisture from accumulating inside the Fire Department Connection. Designed for horizontal installation only. 


                Installation 

                Proper installation of the brass ball drip can be accomplished with standard piping installation tools. Make sure the threads are clean and free from burs and debris. Apply a thread sealant suitable for the materials being joined such as PipeFit, PipeFit AS or PTFE tape. When using a paste type sealant, make sure to brush the sealant deep into the root of the threads. Thread the ball drip into female threads hand tight. Finish tightening with a pipe wrench up to one full turn. Do not over tighten. Over tightening may damage threads and ball drip. Finish piping to allow for proper drainage. Valve opens by force of gravity only. Do not use with more than 1 ft. column of water (water pressure) on the ball check. Use only in the horizontal position.

                0.0
                Add first review
                Not rated yet
                    • Ball Drip Valve - 1/2" x 1/2"

                      Ball Drip Valve - 1/2" x 1/2"


                      The solid brass ball drip is a “ball” type check valve. When properly installed, the internal ball rests in the lower most area of the valve body allowing for proper drainage of moisture accumulation. Upon system pressurization, the internal ball is “pushed” into the small end of the ball drip body closing the opening. When system pressure is removed, the ball returns to its original position. One of the most common uses is on the dry side of the Fire Department Connection valve. This use helps keep moisture from accumulating inside the Fire Department Connection. Designed for horizontal installation only. 


                      Installation 

                      Proper installation of the brass ball drip can be accomplished with standard piping installation tools. Make sure the threads are clean and free from burs and debris. Apply a thread sealant suitable for the materials being joined such as PipeFit, PipeFit AS or PTFE tape. When using a paste type sealant, make sure to brush the sealant deep into the root of the threads. Thread the ball drip into female threads hand tight. Finish tightening with a pipe wrench up to one full turn. Do not over tighten. Over tightening may damage threads and ball drip. Finish piping to allow for proper drainage. Valve opens by force of gravity only. Do not use with more than 1 ft. column of water (water pressure) on the ball check. Use only in the horizontal position.

                      0.0
                      Add first review
                      Not rated yet
                          • Ball Drip Valve - 3/4" x 3/4"

                            Ball Drip Valve - 3/4" x 3/4"


                            The solid brass ball drip is a “ball” type check valve. When properly installed, the internal ball rests in the lower most area of the valve body allowing for proper drainage of moisture accumulation. Upon system pressurization, the internal ball is “pushed” into the small end of the ball drip body closing the opening. When system pressure is removed, the ball returns to its original position. One of the most common uses is on the dry side of the Fire Department Connection valve. This use helps keep moisture from accumulating inside the Fire Department Connection. Designed for horizontal installation only. 


                            Installation 

                            Proper installation of the brass ball drip can be accomplished with standard piping installation tools. Make sure the threads are clean and free from burs and debris. Apply a thread sealant suitable for the materials being joined such as PipeFit, PipeFit AS or PTFE tape. When using a paste type sealant, make sure to brush the sealant deep into the root of the threads. Thread the ball drip into female threads hand tight. Finish tightening with a pipe wrench up to one full turn. Do not over tighten. Over tightening may damage threads and ball drip. Finish piping to allow for proper drainage. Valve opens by force of gravity only. Do not use with more than 1 ft. column of water (water pressure) on the ball check. Use only in the horizontal position.

                            0.0
                            Add first review
                            Not rated yet
                                • 2" Angle Valve

                                  by Allenco Fire

                                  • 2" Female NPT x 2" Female NPT (National Pipe Thread Tapered)
                                  • Suitable as drain valve
                                  • UL Listed


                                  Typically ships in 1-2 days

                                  0.0
                                  Add first review
                                  Not rated yet
                                      • Giacomini A61 Test and Drain - 1"

                                        for testing of fire sprinkler systems

                                        • 1" FNPT x 1" FNPT Threads
                                        • Forged Brass Body
                                        • Sight Glass for Visual Verification of Water Flow
                                        • 1/2" Orifice for 5.6K Factor
                                        • UL Listed / FM Approved
                                        • Rated for 300 PSI


                                        Typically ships in 1-2 days.

                                        0.0
                                        Add first review
                                        Not rated yet
                                            • Giacomini A61 Test and Drain - 1-1/4"

                                              for testing of fire sprinkler systems

                                              • 1.25" FNPT x 1.25" FNPT Threads
                                              • Forged Brass Body
                                              • Sight Glass for Visual Verification of Water Flow
                                              • 1/2" Orifice for 5.6K Factor
                                              • UL Listed / FM Approved
                                              • Rated for 300 PSI


                                              Typically ships in 1-2 days.

                                              0.0
                                              Add first review
                                              Not rated yet
                                                  • Cla-Val 1/2", 3/4", 1" Air Release Valve 300 PSI UL/FM

                                                    1/2", 3/4", and 1"

                                                    Air Release Valves, sometimes referred to as "small orifice valves," continually release unwanted air during system operation to protect against unwanted surges and maintain system efficiency.


                                                    Cla-Val model number 3410-AR 116.3

                                                    Comparable to Val-Matic model number 22.9


                                                    Typically ships in 1-2 days.
                                                    0.0
                                                    Add first review
                                                    Not rated yet
                                                        • 2" Air and Vacuum Valve 300 PSI UL/FM

                                                          Cla-Val 2" Threaded Air and Vacuum Valve

                                                          Designed to protect pipelines from air lock and vacuum collapse, the CLA-VAL Model 33ATD Air Release and Vacuum Breaker Valve eliminates air and prevents vacuum formation in pipelines. A large venting orifice and large float clearances freely exhaust or admits air during pipeline filling or draining. 

                                                          During normal pipeline operation, air accumulation and buoyancy cause the floats to lower or lift. As the water level lowers inside the valve, small amounts of accumulated air are released through the small orifice. 

                                                          Once air is released, the float poppet closes drip tight. Valve servicing is easy because the entire float system can be replaced without removal of the body.


                                                          Typical Applications

                                                          • Vertical Turbine Pumps
                                                          • Split Case Pumps 
                                                          • High Points of Piping Design


                                                          Cla-Val model number 33ATD

                                                          Stock number 20971607F 



                                                          Typically ships in 1-2 days.
                                                          0.0
                                                          Add first review
                                                          Not rated yet

                                                        Bestsellers

                                                        Footer navigation